来宝网Logo

热门词:生物显微镜 水质分析仪 微波消解 荧光定量PCR 电化学工作站 生物安全柜

AED
现在位置首页>实验室常用设备>纯化设备>氮气吹扫仪>乔跃QYLHW-4水质硫化物酸化吹气仪价格
乔跃QYLHW-4水质硫化物酸化吹气仪价格
乔跃QYLHW-4水质硫化物酸化吹气仪价格
  • 乔跃QYLHW-4水质硫化物酸化吹气仪价格

乔跃QYLHW-4水质硫化物酸化吹气仪价格

产品报价:20000元

更新时间:2019/7/2 16:57:28

地:上海

牌:乔跃

号:QYLHW-4

厂商性质: 生产型,贸易型,服务型,

公司名称: 上海乔跃电子有限公司

产品关键词: 水质硫化物酸化吹气仪厂家   六位水质硫化物酸化吹气仪   水质硫化物酸化吹气仪使用   水质硫化物酸化吹气仪   水质硫化物酸化吹气仪  

853
访问人数
0
累计评论


马女士 : (18321004078) (18321004078)

(联系我时,请说明是在来宝网上看到的,谢谢!)


乔跃QYLHW-4水质硫化物酸化吹气仪价格产品介绍:
1、产品原理
水样中的硫化物经酸化,生成的硫化氢随载气(氮气)进入吸收瓶/吸收显色管中被吸收溶液(乙酸锌-乙酸钠溶液或2%化钠溶液)吸收,选择相应的分析方法对吸收瓶/吸收显色管中吸收的硫离子进行分析测定。
2、产品用途
QYLHW-4水质硫化物酸化吹气仪根据水质硫化物的测定-亚甲基蓝分光光度法(碘量法)标准开发生产的。完全满足水质硫化物测定的样品前处理需要。
3、产品执行标准
GB/T16489-1996《水质硫化物的测定--亚甲基蓝分光光度法》
HJ/T600-2000《水质硫化物的测定—碘量法》
 
乔跃QYLHW-4水质硫化物酸化吹气仪价格产品特点:
1、大容量反应瓶,可同时处理多个样品。
2、盐酸口、气体进口、出口三口一体且相互独立,操作会不干扰。
3、恒温水浴加热,具有快速自动恒温控制系统,加热温度可以手动设定。
4、由升降位置固定旋钮调节样品架及配气系统的升降旋转样品架,正面安装样品,操作方便。
5、每个样品的氮气流量独立控制调节或关闭,针阀气体流量计准确控制和显示气体总消耗量。
 
乔跃QYLHW-4水质硫化物酸化吹气仪价格产品参数:
1/产品型号:QYLHW-4
1、样品数:4位或6位(标配4位,6定做)
2、加热方式:自动控温恒温水浴
3、加热功率:l000W,加热均匀
4、氮气流量计控制:0-3L/min
5、温度范围:室温-99.9℃
6、显示方式:数字显示
7、控温精度:±1℃
8、氮气入口压力:0.1Mpa
9、氮气流量支路:0-0.6L/min
10、工作电源:AC(220±22)V,50HZ
11、环境温度:(5-35)℃

12、环境湿度:(0-95)%RH


水质硫化物-酸化吹气仪使用说明
1、打开电源(必须确认水浴锅内已经倒入蒸馏水)散热风扇运转
2、按照国标方法设定恒温水域温度(温控仪)
3、将样品支架升到适当的高度(升降开关)
4、将装有待测水样的反应瓶、吸收管装入样品架
5、连接所有氮气吹管,检查装置的气密性。
6、通氮气,按国标要求将转子流量计调整到适当的流量。控制样品的氮气总消耗量。
7、根据吸收管内气泡上升的速度和数量调整每个样品的氮气流量,使其相同。
8、将样品支架降到恒温水浴中适当的深度。
9、按国标方法的操作步骤进行预处理。
10、预处理过程中随时观察调整氮气总流量及吸收显色管的氮气流量。
11、使用结束将温控仪的温度设定到室温以下,待水浴温度下降后,关闭电源。


1. Turn on the power (it must be confirmed that distilled water has been poured into the water bath pot) and the cooling fan will operate

2. Set the temperature of constant water area (temperature controller) according to national standards

3. Lift the sample bracket to the appropriate height (lifting switch)

4. Put the reaction bottle and absorber into the sample holder to be tested

5. Connect all nitrogen blowpipes and check the air tightness of the device.

6. Through nitrogen, adjust the rotor flowmeter to the appropriate flow rate as required by national standards. Control total nitrogen consumption of the sample.

7. Adjust the nitrogen flow rate of each sample according to the rising speed and quantity of bubbles in the absorption pipe to make it identical.

8. Lower the sample holder to a suitable depth in the constant temperature water bath.

9. Pretreatment is conducted according to the operation steps of the national standard method.

10. During the pretreatment process, adjust the total nitrogen flow and nitrogen flow of the absorption color tube at any time.

11. Set the temperature of the temperature controller below room temperature at the end of use. Turn off the power when the water bath temperature drops.