来宝网Logo

热门词:生物显微镜 水质分析仪 微波消解 荧光定量PCR 电化学工作站 生物安全柜

AED
现在位置首页>计量器具>量规/量仪/卡尺>深度尺>现货N88-12 Reference Pit Gauge
现货N88-12 Reference Pit Gauge
现货N88-12 Reference Pit Gauge
  • 现货N88-12 Reference Pit Gauge

现货N88-12 Reference Pit Gauge

产品报价:询价

更新时间:2023/4/3 18:11:18

地:美国

牌:abqindustrial

号:N88-12

厂商性质: 生产型,

公司名称: 世联博研(北京)科技有限公司

产品关键词: Reference Pit Gauge   参考测坑仪   N88-12   abqindustrial   现货  

1020
访问人数
0
累计评论


王荣 : (18618101725) (18618101725)

(联系我时,请说明是在来宝网上看到的,谢谢!)


N88-12 Reference Pit Gauge

N88-12参考测坑仪


N88-12 Reference Pit Gauges with Dial or Digital Indicators
Western Instruments Pit Gauges assure compliance with vessel, pipeline, tank and OCTG specifications for corrosion and erosion depth measurement.
Measuring Ranges x Resolution: 14 x 0.01 mm or 0.550 inch x 0.001 inch)
5.5" (140 mm) long, 3/4" (19 mm) wide with Inverted V Edge and 2 Adjustable Magnet Cartridges
Available with dial or digital indicators

Western Instruments Dial Indicator Pit Gauges allow the Corrosion Inspector to conveniently measure Pit Depth or material loss in areas of Weight-Loss Corrosion. Various Blades for the Pit Gauges are available for different applications, including the Bridging Pit Gauge which permits Inspectors to Span or Cantilever over large areas of Weight-Loss Corrosion, to get a true measure of Pit Depth.

basic pit gage
Basic
pocket pit gauge
Pocket (reversible)
basic plus pit gauge
Basic Plus
reference gauge
Reference Gauge
reaching gauge
Reaching Pit Gauge
reachingwmag
Reaching Pit Gauge with
Magnetic hold Downs
reachingplus
Reaching + Pit Gauge
reachingplusmag
Reaching Pit Gauge +
Manetic Hold Downs
basicmag
Basic + Pit Gauge with
Magnetic Hold Downs

MODELPART #DESCRIPTION
BasicN88-2Centre Mount 2 1/4" Blade, our most popular model
Basic PlusN88-3Centre Mount 3 1/4" Blade
Basic Plus MagneticN88-3MCentre Mount c/w Two(2) magnetic cartridges 3 1/4" Blade
PocketN88-4Dual Edge Blade (reversible) 1.5" long and spot base
ReachingN88-54 3/4" Blade. End Mount Dial Indicator w/Nose Cutout
Reaching MagneticN88-5M4 3/4" Blade c/w Two(2) magnetic catridges.
Reaching PlusN88-66" Blade. End Mount Dial Indicator w/Nose Cutout
Reaching Plus MagneticN88-6M4 3/4" Blade c/w Two(2) magnetic catridges.


line
Dial and Digital Indicators
line

ABQMetric Dial IndicatorRange:
Resolution:
Dial Diam.
0.0-10mm
0.01mm
35.5mm
Imperial Dial IndicatorRange:
Resolution:
Dial Diam.
0.0-0.5"
0.001"
1.4"
Digital IndicatorRange:
Dial Diam.
0.0-0.5"
0.0-10mm
56mm, 2.2"


line
Measuring Corrosion (Depth)
line

ABQ1-Standard Tip0.040" diam.#1 Contact Point-Standard N88-S
2-Conical Tip0.010" diam.#2 Contact Point-Conical N88-C
3-Needle Tip0.005" diam.#3 Contact Point-Needle N88-N

Western offers a variety of Contact Points, which are all 0.625" (16mm) long. Any ADG Contact point can be used with our special dial indicators, but a different length may affect Height Zeroing, or the vertical position of the Dial Indicator. Contact Points are easily replaced, by extending the Contact Point , and turning it counter clockwise.

line
Zeroing Dial Indicator
line

The vertical position of the Contact Point, needs to be Zeroed with respect to the Knife Edge of the Blade. Zeroing can be accomplished in two ways; by adjusting the Height of the Dial Indicator in the Blade; or by Rotating the outer Bezel Scale while pressing on the Plunger onto a flat surface.

line
Scale Zeroing
line

To quickly check the Zero Point of the Dial indicator, place the Blade on a representative smooth surface. Gently press the Plunger, until the contact point touches the surface. While the contact point is on the surface, loosen the Bezel Lock, and rotate the Bezel Scale until it reads '0' with respect to the pointer.

ABQ

line
Height Zeroing
line

Loosen the Fastener(s) holding the Dial Indicator in place. Hold the Blade firmly on a Flat Surface, and gently press the body of the Dial Indicator down until the contact point touches the flat surface. Carefully re-tighten the Clamp Fastener(s) or the Set Screw. Any fine zeroing can be done by rotating the Bezel Scale on the Dial Indicator.

Height Zeroing should be done, whenever the unit is put into to use.

ABQ

line
Zeroing a Digital Indicator
line

Digital Indicators can be Height Zeroed or Positioned in the same way as a Mechanical Dial Indicator. To Zero the Digital Indicator simply press the Zero Button when the Contact Point is on a reference point. If the Digital Indicator is Height Zeroed, press Zero when the Plunger is fully retracted.

ABQ

To select Metric or Imperial Measurement, simply press the mm/in Button.Whennot in use, press the On/Off Button to turn the Indicator off.

line
Indicator Positioning
line

The position (or rotation) of the Dial indicator can be changed by simply loosening the Clamp Fasteners or Set Screw, and rotate the Dial Indicator about the Blade. After the Dial Indicator is rotated, the unit should be Dial Zeroed.

ABQ

line
Magnetic Hold Downs
line

Magnetic Hold Downs need to be adjusted to fit the surface being tested. If the surface is flat or convex, the Hold Downs can be adjusted, with the Allen Key, to be flush with the knife edge of the blade. However, is the surface is curved (concave), like the inside of a vessel, the Hold Downs need to be adjusted so they dont interfere with the knife edge of the Blade

 ABQ

现货N88-12 Reference Pit Gauge现货N88-12 Reference Pit Gauge现货N88-12 Reference Pit Gauge