来宝网Logo

热门词:生物显微镜 水质分析仪 微波消解 荧光定量PCR 电化学工作站 生物安全柜

AED
现在位置首页>物性测试仪器>无损检测仪器/设备>工业电子内窥镜>现货N88-SPR-D Spiker管道检测套件
现货N88-SPR-D Spiker管道检测套件
现货N88-SPR-D Spiker管道检测套件
  • 现货N88-SPR-D Spiker管道检测套件

现货N88-SPR-D Spiker管道检测套件

产品报价:询价

更新时间:2023/4/3 18:11:18

地:其他国家

牌:abqindustrial

号:N88-SPR-D

厂商性质: 生产型,

公司名称: 世联博研(北京)科技有限公司

产品关键词: Spiker管道检测   N88-SPR-D   abqindustrial   套件   现货  

935
访问人数
0
累计评论


王荣 : (18618101725) (18618101725)

(联系我时,请说明是在来宝网上看到的,谢谢!)


N88-SPR-D Spiker’s Pipeline Inspection Kit

N88-SPR-D Spiker管道检测套件


N88-SPR-D Spiker's Pipeline Inspection Kit

Spiker (Mike West @ Challand Pipeline) has many years of experience in the roll of QA/QC Manager in the Pipeline Construction Industry. In the past he has ordered Pipeline Inspectors Kits (N88-PI), but he often has to deal with magnetized pipe ends. Therefore, Spiker asked Western to produce another Pit Gauge Kit to meet his needs. Pipeline Welding Supervisors and Consultants, are regularly ordering two different instruments from us; a Reaching Pit Gauge, and our W-FI-10 Magnetic Field Indicators. Spiker has gone one step further by adding a Pocket Pit Gauge Blade, so his customized Kit is illustrated below.

line
Contains
line

  • Digital Indicator (N88-D) w/Spare Battery.

  • Reaching Pit Gauge Blade (N88-5-B).

  • Pocket Pit Gauge Blade (N88-4-B).

  • 10-0-10Magnetic Field Indicator (W-FI-10).

  • Hardware (Allan Key, Spare #1 Contact Point)

  • Wood Carrying Case.

  • Operator Instructions

  • Calibration Certificate

Pipeliner’s like the Digital Indicator as it provides both Metric and Imperial (inch) units. The Reaching Blade doesn’t interfere with Yellow Jacket (and other coatings) which typically end far enough-back from the weld, so the Blade is sitting flat on the Pipe surface. The cutaway nose, under the Dial Indicator, permits positioning the Indicator on either side of the weld.

Inspectors like, the Pocket Pit Gauge Blade as it allows measurement on complex curvatures, such as Valve Bodies, Pump Housings, and on the Weld Cap. The Pocket Pit Gauge is just that much smaller than most other Pit Gauge Blades and allows the inspector to measure corrosion in difficult, hard to reach, areas.

The Reaching Pit Gauge is used to measure weld undercut, end alignment differences across the weld as well as Mill Marks. Excessive Undercut creates an area for stress concentrations, and possible cracking. Pipe alignment is necessary to ensure good fit-up geometry for Automatic Welding. Mill Marks are a polite way of describing grinding repairs, or damage that can often happen during handling.

The W-FI-10’s are used to test for residual magnetism in the Weld. Experienced Welders know that when the beveled end of a pipe has a magnetic field over 10 Gauss, welds will be rejected by either UT or X-Ray. Visit www.westerninstruments.com/prewelddemag.html to learn how to remove magnetic fields from pipe before welding

现货N88-SPR-D Spiker管道检测套件现货N88-SPR-D Spiker管道检测套件现货N88-SPR-D Spiker管道检测套件