来宝网Logo

热门词:生物显微镜 水质分析仪 微波消解 荧光定量PCR 电化学工作站 生物安全柜

AED
现在位置首页>计量器具>测绘/长度测量器具>测距仪>现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus
现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus
现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus
  • 现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus

现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus

产品报价:询价

更新时间:2023/4/3 18:11:18

地:美国

牌:abqindustrial

号:N88-11P

厂商性质: 生产型,

公司名称: 世联博研(北京)科技有限公司

产品关键词: Bridging Pit Gauge Plus   N88-11P   桥接测坑仪   abqindustrial   现货  

979
访问人数
0
累计评论


王荣 : (18618101725) (18618101725)

(联系我时,请说明是在来宝网上看到的,谢谢!)


N88-11P Jr. Bridging Pit Gauge Plus

N88-11P Jr.桥接测坑仪


Bridge Type Pit Gauges

Western's advanced Bridging Pit Gauge System? and our new Jr. Bridging Pit Gauge? take over, where the capabilities of our standard Pit Gauges fall short, for evaluating large areas of Weightloss Corrosion. These Bridging Bar type Pit Gauges can also be used to measure Dents and Buckles on Pipelines, Shell Settlement on Storage Tanks, etc. These various forms of Bridging Bars can utilize any of our exclusive Dial Indicators (Imperial, Metric, or Digital), with any of our Custom Engineered Contact Points.

There are several important features to a Segmented Bridge, where various elements (Blades and Tees) are assembled to form a Bridging Bar. Firstly, they can be assembled to follow the contour of a slightly irregular surface. This contouring feature is important for Pipeline, Storage Tank, and Pressure Vessel inspections, where 'hills and valleys' always-exist. Secondly, the models listed below are of a given length, however extra elements can be added to increase their overall length. As illustrated, these units can be assembled in Spanning or Cantilevering configurations, and finally, the Main Blade can be used individually for isolated or cone type Pitting.


Jr. Bridging Pit Gauge? Group

The Jr. Bridging Pit Gauge? Group provides Inspectors with an Economical Alternative to the Bridging Pit Gauge System?. The new Jr. Bridging Pit Gauge? is available as 3 models; the standard Jr. Bridging Pit Gauge?, the Plus, and the Super. The standard Jr. Bridging Pit Gauge?assembles to an overall length of 13?" (340mm). The Jr. Bridging Pit Gauge Plus? can be assembled in either Spanning or Cantilevering Configurations up to 15?" (394mm) long. While the Jr. Bridging Pit Gauge Super? can also be assembled in both Spanning or Cantilevering Configurations, up to 27" (685mm) long.

The Junior's Main Blade, and the optional Extender Blades are fitted with strong magnets that secure any of the Jr. Bridging Pit Gauges? to the surface of the workpiece. These Magnetic Hold Downs have several benefits, such as; Aligning the unit to Concave or Convex surfaces, keeping the operator free to record readings or manipulate the assembly when Scanning through Pits and Weight loss Corrosion. These features position the Plus, and the Super far ahead of any competitive units.


NAMEPART NUMBERDESCRIPTION
Jr. Bridging
Pit Gauge
N88-11Main Blade, Imperial Dial Indicator, 2-Extender Tees, 2-End Blades, Hardware, Extra Contact Point, and Carrying Case.
Jr. Bridging Pit
Gauge Plus
N88-11PMain Blade, Imperial Dial Indicator, Connector Blade, 2-Extender Tees, 2-End Blades, Hardware, Extra Contact Point, and Carrying Case.
Jr. Bridging
Pit Gauge Super
N88-11SMain Blade, Imperial Dial Indicator, 3-Connector Blades, 4-Extender Tees, 2-End Blades, Hardware, Extra Contact Point, and Carrying Case.
Main BladeN88-11-1Center and End Dial Indicator Mounting Positions, Fitted Permanent Magnets. Cutaway Nose for next to welds. 5.5" (144mm) long.
Connector BladeN88-11-2Joins Tee Sections to increase length. Fitted Permanent Magnet. 3.5" (90mm) long.
End BladeN88-11-3Mounts on end of Tee for extra contact. 1.5" (38mm) long.
Doubles as Slider Blade for Plus? and Super?models.
Extender TeeN88-11-5Extends effective length of all models. 5.5" (140mm) long (Longer Tees are optional).
Fastener KitN88-11-7Fasteners, Allen Key, Nylon Thumb Screws, Contact Point.
Carrying CaseN88-11-8Hard Sided Plastic Carrying Case for entire kit.


Assembly

All Bridge type Blades (Main, Extender, End, & Slider) have two distinct sides, that are differentiated by the transverse mounting holes. On one side there is a clearance hole, while on the opposite side the hole is threaded (#10-24 UNC). When assembling, start the fasteners on the Thread Clearance Side of the Blades, so the fasteners can be properly tightened against the Extender Tee's. Do not tighten fasteners if an Extender Tee is not within the Slot area of a Blade.

When assembling the unit, press firmly (as illustrated) on the Extender T, and the Blade you are attaching it to, while tightening the 10-24x?" Button Head Machine Screws with the 1/8" Allen Key. When assembled in this fashion, the overall length of the unit should have a straightness of approximately ±0.015". When more accuracy is required, assemble the unit on a flat surface. If the surface of the workpiece has an irregular surface (slight curve, distinct bend or hills and valleys), simply assemble the Bridging Bar, but do not tighten the fasteners. This will leave the Bridge loose and free to match the contour of the workpiece. When the operator has contoured the assembled Bridge, all the fasteners can be tightened. The operator should be mindful that this contouring assembly will be fine at a given point, however it will need to be checked when the Bridging Bar is repositioned.

bridging pit gauge assembly


Magnetic Hold Downs

Magnetic Hold Downs are intended for Scanning with a Bridging Pit Gauge?, however they can be used on any of the Jr. Bridging Pit Gauge? Group, with a diminished range of motion. Magnetic Hold Downs also provide the inspector with increased mobility, as he is not required to support the Bridging Pit Gauge. The following are instructions for the use, and using, the Magnetic Hold Down Blocks.

Magnetic Hold Down Blocks are designed to easily slide on the Extender Tee's, and are best put in place prior to assembly. With the Bridge assembled, and placed on the workpiece, the entire Bridging Pit Gauge? can travel over a distance of about 9" (290mm). Longitudinal or position measurements of the Bridging Pit Gauge? are taken off the Scales (imperial and metric divisions) that are fastened to the top of the Extender Tees.

Each Magnetic Hold Down is equipped with 2 (two) ?"-20 UNC Nylon Thumb Screws. The Thumb Screws have two purposes, firstly to retain or capture the Magnetic Hold Down onto the Extender Tee. The second use of the Nylon Thumb Screws is to set the tension or to lock the Magnetic Hold Downs. As an example, if the Bridging Pit Gauge? is being used vertically, the operator will want the tension set higher, to keep the unit from sliding. If the Bridging Pit Gauge? is being used on a highly irregular surface, the operator will want the Nylon Thumb Screws set very loose, to allow the Blades to more easily slide over the workpiece.

When setting a Bridge to a Convex surface, such as the OD of a Pipe, or a Concave surface, such as the ID of a Vessel, the Magnetic Hold Downs are used to align the entire assembly. The operator will see this when he attempts to rock the Magnetic Hold Downs from Side to Side. If the unit rocks, the Magnetic Hold Downs are not on the same Longitudinal Axis and must be realigned. When the rocking stops, the operator knows the Bridge is aligned, however, most formed surfaces (pipe, vessels, and tanks) are irregular, so rocking may not be eliminated but must be kept to a minimum to increase measurement accuracy.

 

Magnetic Hold Downs

When preparing for a Scan, the Magnetic Hold Downs should be placed at the correct longitudinal position along the Extender Tee. When general evaluation is being done, and the operator is not recording measurements, place the Magnetic Hold Downs in the Middle of the Tee, to allow movement of the Bridge in both directions. When the operator is going to record measurements, for Plotting a Cross-Section, place the Magnetic Hold Downs at the end position of the scan, then move the bridge to the starting position. The operator takes a reference reading, between a magnetic Hold Down and the Scale on the Tee, before starting the longitudinal movement.


Scanning

Firstly, after a Bridge is assembled, adjusted for the surface contour, and the Magnetic Hold Downs aligned to the surface, the Dial Indicator must be Zeroed (Height or Scale). This will ensure accurate and reproducible measurements. Every time the Bridge is moved to a new location, these parameters (Contour, Alignment, and Hold Down position) must be rechecked and the Dial Indicator re-Zeroed. With the Bridge Type Pit Gauge fully assembled and placed on the workpiece, Pit Depths and Longitudinal travel can be made. This travel permits the Dial Indicator's Contact Point to be moved along the work piece incrementally, to take multiple Pit Measurements. Longitudinal or position measurements are taken off the Scales that are fastened to the Extender Tees. The measurements (depth and length) can then be plotted to obtain a Cross-Sectional View of the corrosion profile.

Scanning through a Pit is covered earlier in this guide, but merits repeating. Western's Dial Indicators have the special Push to Read feature, which allows the operator to Scan through a Pit to obtain an idea of the shape. By placing the index finger on the Plunger, the operator can put a slight amount of pressure onto the Contact Point. The operator then pulls the Pit Gauge Blade through the Pit, paying careful attention that the contact point does not catch on the surface. This allows the operator to watch the depth indications, so he will see both depth and length displacement.

Operators should remember basic survey principles when plotting cross sections. Furthermore, if radial movements are made in increments, and recorded, an entire area of corrosion (lake type) can be mapped.

Cantilever Assembly Scan


Care & Maintenance

Western's ADG Group 1 Dial Indicators (Imperial or Metric), as well as the Digital Indicator were developed for Field Pit Depth Measurement. While ruggedly manufactured, these units should not be dropped or subject to strong Vibration or Impact. While manufactured from Corrosion Resistant Materials, Pit Gauges and their Dial Indicators should be kept clean and dry.  Fit and Finish of Bridge Type Pit Gauges, as well as Standard Pit Gauge parts are very important. Operators should not hesitate to file rough edges, or clean with steel wool or 600 Grit wet/dry abrasive cloth. New parts tend to be tightly fit, and will loosen with use. Care must be taken to ensure fasteners are not cross-threaded.

现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus现货N88-11P Jr.桥接测坑仪,N88-11P Jr. Bridging Pit Gauge Plus